Movincool Classic 18 Spezifikationen

OPERATION MANUALCLASSIC 10 and CLASSIC 18Unit Serial Number Range: 1111XXXX### to Present(From November 2011 to Present)READ THIS MANUAL CAREFULLY FOR

10INSTALLATION (cont.)Moving the UnitUnlock the casters and push the MovinCool unit to a flat level surface and set the casters back to the LOCKED pos

11INSTALLATION (cont.)Plugging in the Unit1. Check the prongs and surface of the power cord plug for dust/dirt. If dust and/or dirt are present, wipe

12INSTALLATION (cont.)Warning Signal Connection (Output Signal Terminal L+ and L-)The controller is equipped with a warning signal output relay type (

13INSTALLATION (cont.)Fire Alarm Control Panel Connection (Input Signal Terminal E+ and E-)The controller is equipped with a normal open input signal,

14INSTALLATION (cont.)LCDI Power Cord InstructionWARNINGCAUTIONProcedure<FRONT VIEW>The LCDI device is a non-serviceable device.Attempting to op

15FEATURES1. A digital electronic control panel, which allows the user to easily control the unit’s operation.2. Digital LED display that indicates:a.

16OPERATIONControl PanelBefore operating the unit, it is important to familiarize yourself with the basic controls located on the control panel.1. COO

17OPERATION (cont.)Control Panel (cont.)LED Display DescriptionsIn normal operation, the LED displays the following descriptions.Note: The ROOM TEMP d

18OPERATION (cont.)Operating in COOL Mode1. The unit can be operated in COOL mode by pressing the COOL ON/OFF button.Note: In COOL mode the unit can o

19OPERATION (cont.)Operating in FAN ONLY Mode1. The unit can also be operated in FAN ONLY mode by pressing FAN button.2. The unit can only be turned o

SERIAL NUMBER LOCATION AND IDENTIFICATIONNameplate Label PositionNameplate LabelCOOLING AMPS. WITH PUMPCOMPR. OUTPUTREFRIGERANT/TOTAL CHARGEDESIGN PRE

20OPERATION (cont.)Operating ModesThe Classic 10 and Classic 18 can be operated in two modes, FAN ONLY and COOL. When in FAN ONLY mode, the unit circu

21OPERATION (cont.)Self-Diagnostic CodesSelf-diagnostic codes are displayed on the control board under the following conditions.Contact your MovinCool

22OPERATION (cont.)Empty the Drain TankDuring COOL mode, condensate water accumulates in the drain tank. When the drain tank becomes full, the LED dis

23OPERATION (cont.)Condensate Pump Kit (Optional for Classic 10)A condensate pump kit is available to allow continuous operation and to eliminate the

24OPERATION (cont.)Condensate Pump Kit (Optional for Classic 18)A condensate pump kit is available to allow continuous operation and to eliminate the

25INSPECTION & MAINTENANCEEmpty the Drain TankTo empty the drain tank, refer to instructions on page 22.Clean the Air FiltersClean the air filters

26INSPECTION & MAINTENANCE (cont.)In-Season/Off-Season Inspection & MaintenanceIn-Season1. Check the prongs and surface of the power cord plug

27TROUBLESHOOTINGCheck the following items before calling your MovinCool reseller or a qualified technician.If conditions persist after the above acti

28TECHNICAL SPECIFICATIONS OF CLASSIC 10• Specifications are subject to change without notice.Note:*1: Measured at 3 feet (1.0 m) from surface of the

29TECHNICAL SPECIFICATIONS OF CLASSIC 18• Specifications are subject to change without notice.Note:*1: Measured at 3 feet (1.0 m) from surface of the

OPERATION MANUALCLASSIC 10 and CLASSIC 18

WARRANTY STATEMENTDENSO PRODUCTS AND SERVICES AMERICAS, INC. ("DENSO") warrants its MOVINCOOL Products only to the extent stated in its offi

P/N: 484007-3631EN Second Issue: April 2013

Table of ContentsSERIAL NUMBER LOCATION AND IDENTIFICATION ... 2FOREWORD ...

5FOREWORDCongratulations on purchasing the MovinCool portable air conditioner. This manual explains how to install and operate the MovinCool Classic 1

6GENERAL WARNINGS & CAUTIONS1. All electrical work, if necessary, should only be performed by qualified electrical personnel. Repair to electrical

7INVENTORY & ASSEMBLYInventoryAfter unpacking your MovinCool unit, please check to make sure you have the following items:1. Classic 10 or Classic

8INVENTORY & ASSEMBLY (cont.)AssemblyCAUTION: Before assembling make sure the unit is on a flat, level surface and the casters are in the LOCKED p

9INSTALLATIONChoosing an Installation SiteCAUTION: Following are some precautions to consider before choosing your installation site. Please review ca