Movincool Classic Plus 14 Spezifikationen

OPERATION MANUALCLASSIC PLUS 14 and CLASSIC PLUS 26Unit Serial Number Range: 0711XXXX### to Present(From July 2011 to Present)READ THIS MANUAL CAREFUL

10INSTALLATION (cont.)Moving the UnitUnlock the casters and push the MovinCool unit to a flat level surface and set the casters back to the LOCKED pos

11INSTALLATION (cont.)Plugging in the Unit1. Check the prongs and surface of the power cord plug for dust/dirt. If dust and/or dirt are present, wipe

12INSTALLATION (cont.)Warning Signal Connection (Output Signal Terminal L+ and L-)The controller is equipped with a warning signal output relay type (

13INSTALLATION (cont.)Fire Alarm Control Panel Connection (Input Signal Terminal E+ and E-)The controller is equipped with a normal open input signal,

14INSTALLATION (cont.)LCDI Power Cord InstructionWARNINGCAUTIONProcedure<FRONT VIEW>The LCDI device is a non-serviceable device.Attempting to op

15FEATURES1. A digital electronic control panel, which allows the user to easily control the unit's operation.2. Dual fan speeds (either HIGH or

16OPERATIONControl PanelBefore operating the unit, it is important to familiarize yourself with the basic controls located on the control panel.1. COO

17OPERATION (cont.)Control Panel (cont.)5. SET CLOCK Button Press to set clock (day and time).6. SET PROG Button Press to set or view program.7. RUN/S

18OPERATION (cont.)Control Panel (cont.)LCD IndicatorsNote: ROOM TEMP display range is from 16 °F (-9 °C) to 109 °F (42 °C). When the display value is

19OPERATION (cont.)Control Panel (cont.)LCD Indicators (cont.)15. STOP Illuminates to indicate program stop time.16. CLOCK Illuminates to indicate clo

SERIAL NUMBER LOCATION AND IDENTIFICATIONNameplate Label PositionNameplate LabelCOOLING AMPS. WITH PUMPCOMPR. OUTPUTREFRIGERANT/TOTAL CHARGEDESIGN PRE

20OPERATION (cont.)Set ClockPrior to operating the Classic Plus 14 or Classic Plus 26 users should set the clock of the controller to the correct time

21OPERATION (cont.)Operating in FAN ONLY Mode1. The unit can also be operated in FAN ONLY mode by pressing FAN HI/LO button (LCD indicates “FAN HI/LO”

22OPERATION (cont.)How to Set a ProgramSET START TIME1. Press and hold the SET PROG button for 3 sec or until beep.2. Press SET TEMP buttons to scroll

23OPERATION (cont.)How to View and Delete Program1. Press and hold the SET PROG button for 3 sec until beep.2. To view edited program - While pressing

24OPERATION (cont.)Operating ModesThe Classic Plus 14 and Classic Plus 26 can be operated in two modes, FAN ONLY and COOL. When in FAN ONLY mode, the

25OPERATION (cont.)Self-Diagnostic CodesSelf-diagnostic codes are displayed on the control board under the following conditions.Contact your MovinCool

26OPERATION (cont.)Empty the Drain TankDuring COOL mode, condensate water accumulates in the drain tank. When the drain tank becomes full, the “TANK F

27OPERATION (cont.)Condensate Pump Kit (Optional for Classic Plus 14)A condensate pump kit is available to allow continuous operation and to eliminate

28OPERATION (cont.)Condensate Pump Kit (Optional for Classic Plus 26)A condensate pump kit is available to allow continuous operation and to eliminate

29DAILY INSPECTION & MAINTENANCEEmpty the Drain TankTo empty the drain tank, refer to instructions on page 26.Clean the Air FiltersClean the air f

OPERATION MANUALCLASSIC PLUS 14 and CLASSIC PLUS 26

30DAILY INSPECTION & MAINTENANCE (cont.)In-Season/Off-Season Inspection & MaintenanceIn-Season1. Check the prongs and surface of the power cor

31TROUBLESHOOTINGCheck the following items before calling your MovinCool reseller or a qualified technician.If conditions persist after the above acti

32TECHNICAL SPECIFICATONSITEMS/FEATURES Classic Plus 14 Classic Plus 26Rating ConditionsDry bulbWet bulbHumidity95 °F (35 °C)83 °F (28 °C)60 %RH95 °F

33TECHNICAL SPECIFICATONS (cont.)ITEMS/FEATURES Classic Plus 14 Classic Plus 26Safety DevicesCompressor overload protectorFan motor protectorAnti-free

WARRANTY STATEMENTDENSO PRODUCTS AND SERVICES AMERICAS, INC. ("DENSO") warrants its MOVINCOOL Products only to the extent stated in its offi

P/N: 484007-3611EN Second Issue: April 2013

Table of ContentsSERIAL NUMBER LOCATION AND IDENTIFICATION ... 2FOREWORD ...

5FOREWORDCongratulations on purchasing the MovinCool portable air conditioner. This manual explains how to install and operate the MovinCool Classic P

6GENERAL WARNINGS & CAUTIONS1. All electrical work, if necessary, should only be performed by qualified electrical personnel. Repair to electrical

7INVENTORY & ASSEMBLYInventoryAfter unpacking your MovinCool unit, please check to make sure you have the following items:1. Classic Plus 14 or Cl

8INVENTORY & ASSEMBLY (cont.)AssemblyCAUTION: Before assembling make sure the unit is on a flat, level surface and the casters are in the LOCKED p

9INSTALLATIONChoosing an Installation SiteCAUTION: Following are some precautions to consider before choosing your installation site. Please review ca